Aiolos Posted September 6, 2007 Report Share Posted September 6, 2007 Λοιπον εχω ενα προβληματακι με τα εξης πακετα του Ubuntu.Με το tzdata και το libc6 των οποιων η τελευταια εκδοση μου κανει συνεχεια conflict.Το αποτελεσμα ειναι να μη μπορω να χρησιμοποιησω τα headers που δινει το libc6 και να μην μπορω να εγκαταστησω τιποτα ουτε με make install ουτε με apt-get install. Δοκιμασα να γυρισω σε παλιοτερη εκδοση τα πακετα και τα ubuntu πηραν το δισακι τους και φυγαν. :headb: Ξερει κανεις ενα αντιστοιχο προγραμμα με το speedfan των windose στα ubuntu?Ο ανεμιστηρας σε full ενταση κανει λες και απογειωνεται concord. :headb: :headb: Quote Link to comment Share on other sites More sharing options...
Αυγερινός Posted September 6, 2007 Report Share Posted September 6, 2007 Για αντίστοιχο του speedfan δες εδώ: http://ubuntuguide.org/wiki/Ubuntu:Feisty#...28lm-sensors.29 Για το πρόβλημα που έχεις άνοιξε μια κονσόλα και δώσε: sudo killall apt sudo killall apt-get sudo killall aptitude sudo killall dpkg sudo dpkg --configure -a sudo aptitude dist-upgrade -f και μάλλον θα είσαι εντάξει. Quote Link to comment Share on other sites More sharing options...
Aiolos Posted September 6, 2007 Author Report Share Posted September 6, 2007 Αυγερινε εισαι αστερι(κυριολεκτικα) .Τα headers δουλευουν.Οσο για το lm-sensors παρολο που που το εχω εγκατεστημενο κανω sensors-detect κα δε βρισκει τιποτα μου λεει οτι χρειαζεται ενα eeprom και κυριως το coretemp λογω core2duo.οσο και εαν εψαξα δεν βρηκα αλλο εκτος απο το coretemp.h και δοκιμαζοντας το make -f η to gcc παιρνω μηνυμα missing separator at line 1.Καπου διαβασα οτι μπορει να φταιει και η Mobo μου. Τα ubuntu αντεπιτιθονται.... Quote Link to comment Share on other sites More sharing options...
Αυγερινός Posted September 6, 2007 Report Share Posted September 6, 2007 Είναι αρκετά πιθανό να μην υποστηρίζεται ο fan controller της μητρικής σου, αλλά πλην το εξαντλήσουμε ας προσπαθήσουμε τουλάχιστο. Λοιπόν θέλω να δώσεις το output της κονσόλας ακριβώς όπως στο βγάζει (copy paste εδώ) όταν τρέχεις sensors-detect. Επίσης θέλω ακριβές μοντέλο μητρικής. Quote Link to comment Share on other sites More sharing options...
Aiolos Posted September 7, 2007 Author Report Share Posted September 7, 2007 # sensors-detect revision 4348 (2007-03-18 02:45:21 -0700) This program will help you determine which kernel modules you need to load to use lm_sensors most effectively. It is generally safe and recommended to accept the default answers to all questions, unless you know what you're doing. We can start with probing for (PCI) I2C or SMBus adapters. Do you want to probe now? (YES/no): y Probing for PCI bus adapters... Use driver `i2c-i801' for device 0000:00:1f.3: Intel 82801H ICH8 We will now try to load each adapter module in turn. Module `i2c-i801' already loaded. If you have undetectable or unsupported adapters, you can have them scanned by manually loading the modules before running this script. To continue, we need module `i2c-dev' to be loaded. Do you want to load `i2c-dev' now? (YES/no): y Module loaded successfully. We are now going to do the I2C/SMBus adapter probings. Some chips may be double detected; we choose the one with the highest confidence value in that case. If you found that the adapter hung after probing a certain address, you can specify that address to remain unprobed. Next adapter: SMBus I801 adapter at 0400 (i2c-0) Do you want to scan it? (YES/no/selectively): y Client found at address 0x50 Handled by driver `eeprom' (already loaded), chip type `eeprom' Some chips are also accessible through the ISA I/O ports. We have to write to arbitrary I/O ports to probe them. This is usually safe though. Yes, you do have ISA I/O ports even if you do not have any ISA slots! Do you want to scan the ISA I/O ports? (YES/no): y Probing for `National Semiconductor LM78' at 0x290... No Probing for `National Semiconductor LM78-J' at 0x290... No Probing for `National Semiconductor LM79' at 0x290... No Probing for `Winbond W83781D' at 0x290... No Probing for `Winbond W83782D' at 0x290... No Probing for `Silicon Integrated Systems SIS5595'... No Probing for `VIA VT82C686 Integrated Sensors'... No Probing for `VIA VT8231 Integrated Sensors'... No Probing for `IPMI BMC KCS' at 0xca0... No Probing for `IPMI BMC SMIC' at 0xca8... No Some Super I/O chips may also contain sensors. We have to write to standard I/O ports to probe them. This is usually safe. Do you want to scan for Super I/O sensors? (YES/no): y Probing for Super-I/O at 0x2e/0x2f Trying family `ITE'... No Trying family `National Semiconductor'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Fintek'... Yes Found `Winbond W83627DHG Super IO Sensors' Success! (address 0x290, driver `w83627ehf') Probing for Super-I/O at 0x4e/0x4f Trying family `ITE'... No Trying family `National Semiconductor'... No Trying family `SMSC'... No Trying family `VIA/Winbond/Fintek'... No Some CPUs or memory controllers may also contain embedded sensors. Do you want to scan for them? (YES/no): y AMD K8 thermal sensors... No Intel Core family thermal sensor... Success! (driver `coretemp') Intel AMB FB-DIMM thermal sensor... No Now follows a summary of the probes I have just done. Just press ENTER to continue: y Driver `eeprom' (should be inserted): Detects correctly: * Bus `SMBus I801 adapter at 0400' Busdriver `i2c-i801', I2C address 0x50 Chip `eeprom' (confidence: 6) EEPROMs are *NOT* sensors! They are data storage chips commonly found on memory modules (SPD), in monitors (EDID), or in some laptops, for example. Driver `w83627ehf' (should be inserted): Detects correctly: * ISA bus, address 0x290 Chip `Winbond W83627DHG Super IO Sensors' (confidence: 9) Driver `coretemp' (should be inserted): Detects correctly: * Chip `Intel Core family thermal sensor' (confidence: 9) I will now generate the commands needed to load the required modules. Just press ENTER to continue: y To make the sensors modules behave correctly, add these lines to /etc/modules: #----cut here---- # I2C adapter drivers i2c-i801 # Chip drivers eeprom w83627ehf # Warning: the required module coretemp is not currently installed # on your system. For status of 2.6 kernel ports check # http://www.lm-sensors.org/wiki/Devices. If driver is built # into the kernel, or unavailable, comment out the following line. coretemp #----cut here-- mobo---->asus p5b oxi deluxe ktl Quote Link to comment Share on other sites More sharing options...
Αυγερινός Posted September 7, 2007 Report Share Posted September 7, 2007 Άρα είσαι οκ. Σου βρήκε τα modules: To make the sensors modules behave correctly, add these lines to /etc/modules: #----cut here---- # I2C adapter drivers i2c-i801 # Chip drivers eeprom w83627ehf # Warning: the required module coretemp is not currently installed # on your system. For status of 2.6 kernel ports check # http://www.lm-sensors.org/wiki/Devices. If driver is built # into the kernel, or unavailable, comment out the following line. #coretemp #----cut here-- Οπότε ανοίγες ως root το /etc/modules και κάνεις copy paste το παραπάνω. Κάνε και ένα restart μετά να φορτωθούν σωστά τα modules. Αν δεν σου δουλέψει σημαίνει ότι το module coretemp δεν είναι buildin στον πυρήνα σου και θα πρέπει να βρούμε ένα. Quote Link to comment Share on other sites More sharing options...
Aiolos Posted September 8, 2007 Author Report Share Posted September 8, 2007 Δοκιμασα με το me to gedit να το γραψω αλλα δεν ειχε αποτελεσμα μετα απο πολλες προσπαθειες. Αν δεν σου δουλέψει σημαίνει ότι το module coretemp δεν είναι buildin στον πυρήνα σου και θα πρέπει να βρούμε ένα. Ναι αυτο πιστευω καθως το kernel μου ειναι παλαιοτερo (2.6.16) απο την εκδοση που το εχει buildin (2.6.22 και μετα).Αυτο που δεν καταλαβα ειναι αν θα επρεπε να εγκαταστησω την 64Bit εκδοση των ubuntu η οποια θα εχει πιθανον το συγκεκριμενο kernel η να το παλεψω με την τωρινη μου που ειναι για x86 επεξεργαστες. Αν οχι με την 64bit πως μπορω να αναβαθμισω το τωρινο kernel?Μηπως εχω κανει καμμια γκαφα παλι? Quote Link to comment Share on other sites More sharing options...
Αυγερινός Posted September 8, 2007 Report Share Posted September 8, 2007 Ποια έκδοση ubuntu τρέχεις; Η τρέχουσα (Feisty Fawn (7.04)) τρέχει τον 2.6.22.x και στην x86 και στην x8-64 αρχιτεκτονική. Σε Edgy (6.10) είσαι; Δεν κάνεις κανένα upgrade; Σύντομα θα είσαι 2 εκδόσεις πίσω, αφού σε λίγο βγαίνει η Gutsy Gibbon (7.10) και εκεί περιπλέκονται τα πράγματα στο upgrade. Quote Link to comment Share on other sites More sharing options...
Aiolos Posted September 8, 2007 Author Report Share Posted September 8, 2007 (edited) Λαθος δικο μου, ειχα το 2.6.20-16 kernel οχι το 2.6.16-20(Feisty fawn παντα).Για καλο και για κακο τα ξαναεγκατεστησα με την 64bit εκδοση και ειδα οτι και αυτο ειχε την 2.6.20.Ετσι εκανα update μονος μου στο kernel στην εκδοση 2.6.22-11 η οποια εχει buildin το coretemp. Με τις οδηγιες του http://ubuntuguide.org/wiki/Ubuntu:Feisty#...28lm-sensors.29 τα εκανα ολα οσα χρειαζοταν και την τελευταια στιγμη οταν πατησα sensors μου εβγαλε w83627dhg-i2c-9191-290 ERROR: Can't get adapter or algorithm?!? το οποιο ειναι τουλαχιστον μια βελτιωση καθως παντα μου ελεγε no sensors found μαλλον δε θελει η μητρικη... Edited September 8, 2007 by Aiolos Quote Link to comment Share on other sites More sharing options...
Αυγερινός Posted September 8, 2007 Report Share Posted September 8, 2007 Ναι έχεις δίκιο, ο kernel στο feisty είναι ο 20-16 όχι ο 22-x. Καλό είναι να μην βάζεις κάτι εκτός package management system γιατί είναι πολύ πιθανό να σου σπάσει η διανομή. Και αν αυτό είναι μια φορά πιθανό με ένα πρόγραμμα, σκέψου πόσες φορές περισσότερο είναι με τον kernel. Δηλαδή kernels, headers, libs κλπ ΠΑΝΤΑ ΚΑΙ ΜΟΝΟ μέσα απ'το Synaptic (ή το Adept ή όποιο frontend του apt χρησιμοποιείς). Το ότι και εδώ έγινε μέσω synaptic δεν λέει κάτι γιατί το repository που του έβαλες για να τραβήξει τον kernel τώρα δεν υπάρχει (το έβγαλες) και δημιουργεί conflict. Θα σου πρότεινα να αναιρέσεις ό,τι βήμα έκανες, να μπουτάρεις δηλαδή με τον παλιό σου kernel και μετά να κάνεις ένα upgrade σε gutsy (που ούτως η άλλως όπου να'ναι βγαίνει και στη φάση που είναι δεν έχει προβλήματα). Δοκίμασε αν μετά το upgrade δεν παίζει, να τρέξεις το lm-sensors ως root. Ορίστε και οι εντολές: sudo update-manager -c -d Αν δεν σου δουλέψει έτσι, τότε κάνε το εξής: sudo sed -e 's/\sfeisty/ gutsy/g' -i /etc/apt/sources.list sudo apt-get update sudo apt-get upgrade Quote Link to comment Share on other sites More sharing options...
Aiolos Posted September 11, 2007 Author Report Share Posted September 11, 2007 Δυστυχως ουτε και αυτο πετυχε.Ετσι αποφασισα να περιμενω την καινουργια εκδοση που μου ειπες οταν βγει επισημα...Αλλιως θα περασω σε ποιο δραστικα μετρα του στυλ Quote Link to comment Share on other sites More sharing options...
Aiolos Posted October 10, 2007 Author Report Share Posted October 10, 2007 (edited) Επιτελους μετα απο την τελευταια αναβαθμιση δουλεψε.... :smilewink: και να το sensors w83627dhg-isa-0290 Adapter: ISA adapter VCore: +1.16 V (min = +0.00 V, max = +1.74 V) in1: +12.20 V (min = +0.11 V, max = +5.44 V) ALARM AVCC: +3.23 V (min = +1.89 V, max = +0.98 V) ALARM 3VCC: +3.23 V (min = +0.00 V, max = +3.22 V) ALARM in4: +1.58 V (min = +1.03 V, max = +1.02 V) ALARM in5: +1.58 V (min = +0.10 V, max = +0.68 V) ALARM in6: +5.53 V (min = +4.33 V, max = +0.46 V) ALARM VSB: +3.23 V (min = +0.19 V, max = +1.06 V) ALARM VBAT: +3.01 V (min = +0.78 V, max = +2.05 V) ALARM Case Fan: 0 RPM (min = 10546 RPM, div = 128) ALARM CPU Fan: 2766 RPM (min = 2537 RPM, div = 4) Aux Fan: 0 RPM (min = 10546 RPM, div = 128) ALARM fan4: 0 RPM (min = 10546 RPM, div = 128) ALARM fan5: 0 RPM (min = 10546 RPM, div = 128) ALARM Sys Temp: +44°C (high = +4°C, hyst = +57°C) CPU Temp: +49.0°C (high = +80.0°C, hyst = +75.0°C) AUX Temp: +119.0°C (high = +80.0°C, hyst = +75.0°C) ALARM coretemp-isa-0000 Adapter: ISA adapter Core 0: +45°C (high = +85°C) coretemp-isa-0001 Adapter: ISA adapter Core 1: +45°C (high = +85°C) τωρα πιστευω θα καταφερω να αλλαξω αυτο το καταραμενο 2766rpm που μου σπαει τα νευρα update:και ναι το εφτιαξα Edited October 11, 2007 by Aiolos Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.